first_power_up
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
first_power_up [2018/07/10 15:24] – akuzmuk | first_power_up [2024/01/16 09:19] (current) – [Preparation for work] emozolyak | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== First power-up ====== | ====== First power-up ====== | ||
+ | {{ network: | ||
===== Preparation for work ===== | ===== Preparation for work ===== | ||
Before you can start WebHMI for the first time, you need to take some preparatory steps. | Before you can start WebHMI for the first time, you need to take some preparatory steps. | ||
+ | <WRAP center round important 60%> | ||
+ | The storage device is set by default to SD card. You can use USB drives either. If you change storage device and install different one from the currently set in the WebHMI' | ||
+ | {{: | ||
+ | </ | ||
- | | + | |
+ | | ||
- By default, the WebHMI' | - By default, the WebHMI' | ||
- When connecting the RS485 bus, make sure that not only lines A and B are connected but also their common wire that equalizes the potentials between the WebHMI and other devices on the bus is connected too. This is especially true if the line is long or the devices are powered by different power sources. | - When connecting the RS485 bus, make sure that not only lines A and B are connected but also their common wire that equalizes the potentials between the WebHMI and other devices on the bus is connected too. This is especially true if the line is long or the devices are powered by different power sources. | ||
Line 14: | Line 20: | ||
If the SD card is not detected, the WebHMI will flash three LEDs (Error, WWW, and VPN). After 20 flashes, the system boots but not all services are started. During the next minute, watchhog will see that there is no SD card and will reboot the system. In this way, the system will constantly reboot until an SD card is inserted. | If the SD card is not detected, the WebHMI will flash three LEDs (Error, WWW, and VPN). After 20 flashes, the system boots but not all services are started. During the next minute, watchhog will see that there is no SD card and will reboot the system. In this way, the system will constantly reboot until an SD card is inserted. | ||
+ | |||
+ | ==== Front panel conteols designations ==== | ||
+ | {{ :: | ||
+ | |||
===== Access to the web interface ===== | ===== Access to the web interface ===== | ||
Line 19: | Line 29: | ||
==== Wireless connection over Wi-Fi ==== | ==== Wireless connection over Wi-Fi ==== | ||
- | By default, the WebHMI wireless interface is configured in an access point mode with DHCP enabled and disabled security. Thus, your laptop or tablet can simply be connected to the WebHmi | + | By default, the WebHMI wireless interface is configured in an access point mode with DHCP enabled and disabled security. Thus, your laptop or tablet can simply be connected to the **WebHMI** |
==== Wired connection ==== | ==== Wired connection ==== | ||
- | WebHmi | + | WebHMI |
+ | {{ network: | ||
- | Further actions may vary depending on the OS (example | + | To get access to web interface please configure your network adapter either in DHCP client mode or with following settings: |
- | - Connect the Ethernet cable to the LAN port | + | IP address: **192.168.1.2** \\ |
- | - Configure the network connection properties in the PC - the IP address' '[192.168.1.2]' and the subnet | + | Subnet |
- | Link 001.png | + | Once network cable is connected check the connection by pinging 192.168.1.1 (execute the command 'ping 192.168.1.1' |
+ | |||
+ | If there is a link, but for some reason you can not access the site - check if the proxy server is being used in the browser settings. | ||
+ | |||
+ | TIP. For correct operation of the web-interface of the system, | ||
+ | use the latest version of Google Chrome web-browser. | ||
+ | |||
+ | ===== Login to the web interface ===== | ||
+ | To enter the new device, you must use default credentials: | ||
+ | |||
+ | ^ Login | admin | | ||
+ | ^ Password | admin | | ||
+ | |||
+ | {{ network: | ||
+ | |||
+ | On login screen at the bottom section you can find current version of firmware and link to network setup interface. | ||
+ | |||
+ | After logging in by default, you will be taken to the registers configuration page: | ||
+ | |||
+ | ==== An "after login" project view after 3.6 fw ==== | ||
+ | |||
+ | (in the Setup/ | ||
+ | === Moon color theme === | ||
+ | |||
+ | {{ network: | ||
+ | |||
+ | === Mars color theme === | ||
+ | {{ network: | ||
- | - Check the connection. Call the " | ||
- | Link 002.png | ||
- | If there is a link, but for some reason you can not access the site - check if the proxy server is being used in the browser settings. | ||
- | Link 003.png | + | ==== An "after login" project view before 3.6 fw==== |
- | TIP. For correct operation of the web-interface of the system, use the latest version of Google Chrome web-browser. | + | {{ network:new-signin.png? |
first_power_up.1531236260.txt.gz · Last modified: 2018/07/10 15:24 by akuzmuk