first_power_up
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
first_power_up [2018/07/10 15:20] – akuzmuk | first_power_up [2024/01/16 09:19] (current) – [Preparation for work] emozolyak | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== First power-up ====== | ====== First power-up ====== | ||
+ | {{ network: | ||
===== Preparation for work ===== | ===== Preparation for work ===== | ||
Before you can start WebHMI for the first time, you need to take some preparatory steps. | Before you can start WebHMI for the first time, you need to take some preparatory steps. | ||
+ | <WRAP center round important 60%> | ||
+ | The storage device is set by default to SD card. You can use USB drives either. If you change storage device and install different one from the currently set in the WebHMI' | ||
+ | {{: | ||
+ | </ | ||
- | | + | |
+ | | ||
- By default, the WebHMI' | - By default, the WebHMI' | ||
- When connecting the RS485 bus, make sure that not only lines A and B are connected but also their common wire that equalizes the potentials between the WebHMI and other devices on the bus is connected too. This is especially true if the line is long or the devices are powered by different power sources. | - When connecting the RS485 bus, make sure that not only lines A and B are connected but also their common wire that equalizes the potentials between the WebHMI and other devices on the bus is connected too. This is especially true if the line is long or the devices are powered by different power sources. | ||
Line 14: | Line 20: | ||
If the SD card is not detected, the WebHMI will flash three LEDs (Error, WWW, and VPN). After 20 flashes, the system boots but not all services are started. During the next minute, watchhog will see that there is no SD card and will reboot the system. In this way, the system will constantly reboot until an SD card is inserted. | If the SD card is not detected, the WebHMI will flash three LEDs (Error, WWW, and VPN). After 20 flashes, the system boots but not all services are started. During the next minute, watchhog will see that there is no SD card and will reboot the system. In this way, the system will constantly reboot until an SD card is inserted. | ||
+ | |||
+ | ==== Front panel conteols designations ==== | ||
+ | {{ :: | ||
+ | |||
+ | |||
+ | ===== Access to the web interface ===== | ||
+ | Work with WebHMI takes place over the network. All settings, including project configuration, | ||
+ | |||
+ | ==== Wireless connection over Wi-Fi ==== | ||
+ | By default, the WebHMI wireless interface is configured in an access point mode with DHCP enabled and disabled security. Thus, your laptop or tablet can simply be connected to the **WebHMI** network (the settings will be made automatically), | ||
+ | |||
+ | ==== Wired connection ==== | ||
+ | WebHMI has 2 Ethernet ports: a LAN configured as a DHCP server and a WAN configured as a DHCP client with incoming connections disabled by default in the firewall. Thus, access to the web interface of the system can only be obtained from the LAN port. | ||
+ | |||
+ | {{ network: | ||
+ | |||
+ | To get access to web interface please configure your network adapter either in DHCP client mode or with following settings: | ||
+ | |||
+ | IP address: **192.168.1.2** \\ | ||
+ | Subnet mask: **255.255.255.0** | ||
+ | |||
+ | Once network cable is connected check the connection by pinging 192.168.1.1 (execute the command 'ping 192.168.1.1' | ||
+ | |||
+ | If there is a link, but for some reason you can not access the site - check if the proxy server is being used in the browser settings. | ||
+ | |||
+ | TIP. For correct operation of the web-interface of the system, | ||
+ | use the latest version of Google Chrome web-browser. | ||
+ | |||
+ | ===== Login to the web interface ===== | ||
+ | To enter the new device, you must use default credentials: | ||
+ | |||
+ | ^ Login | admin | | ||
+ | ^ Password | admin | | ||
+ | |||
+ | {{ network: | ||
+ | |||
+ | On login screen at the bottom section you can find current version of firmware and link to network setup interface. | ||
+ | |||
+ | After logging in by default, you will be taken to the registers configuration page: | ||
+ | |||
+ | ==== An "after login" project view after 3.6 fw ==== | ||
+ | |||
+ | (in the Setup/ | ||
+ | === Moon color theme === | ||
+ | |||
+ | {{ network: | ||
+ | |||
+ | === Mars color theme === | ||
+ | {{ network: | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ==== An "after login" project view before 3.6 fw==== | ||
+ | |||
+ | {{ network: | ||
+ |
first_power_up.txt · Last modified: 2024/01/16 09:19 by emozolyak